几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量  


返回   几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 » 三维空间:产品设计或CAX软件使用 » CAD设计 » 产品功能分析
用户名
密码
注册 帮助 会员 日历 银行 搜索 今日新帖 标记论坛为已读


回复
 
主题工具 搜索本主题 显示模式
旧 2009-09-10, 11:26 AM   #1
huangyhg
超级版主
 
huangyhg的头像
 
注册日期: 04-03
帖子: 18592
精华: 36
现金: 249466 标准币
资产: 1080358888 标准币
huangyhg 向着好的方向发展
默认 location of control joints in brick veneer

location of control joints in brick veneer
we provide shelf angle to support brick veneer and also there is a limitation to the height of the veneer. just need to know that control joint in veneer is dictated by architect or structures. also is there any limitation regarding the depth available due the structural deflection reflecting in control joint. can we make it 1" deflection in control joint. i am talking here for a 2 stories shopping mall facade.

check out our whitepaper library.
ali,
the location and design of control joints in brick veneer, both horizontal and vertical, must be the subject of coordination/negotiation between the architect and structural engineer. i doubt that many architects would agree to a control joint allowing 1" deflection. assuming 50% deformation of the sealant (which may not be achievable), the joint would have to start at 2" thick. also, deflection of this magnitude would probably result in cracking of the brickwork above the joint. i think you need to make the supporting structure stiffer.
thanks hookie,
is there any practical limitation to provide control joint horizontally. what is the maximum practical depth veneer can go vertically if supported on foundation and if supported on shelf angle with no control joint.
a continuous shelf angle is a control joint. horizontal control joints are less of an issue from a building movement standpoint than vertical joints (they are essentially always in compression, but subject to shear in conjunction with the vertical joints).
keep in mind that horizontal brick joints must not only accomadate the deflection of the structure supporting the brick above the joint, but also the swelling and thermal expansion of the brick below the joint. swelling and thermal expansion can be a significant percentage of the total movement needed to be accomadated.

the international building code limits deflection of horizontal
the spacing depends on how much of a control freek you are...
mike mccann
mmc engineering
appreciate guys for useful information provided.
there are three different ways to do the brick at shelf angles.
1) typical brick above and below shelf angle. this unfortunately will give the thickest joint = shelf angle thickness + 1/2 x compressible filler.
2) notched brick above (to accomodate shelf angle thickness)
with typical brick below. compressible filler thickness = mortar joint.
3) typical brick above and notched brick below. can accomodate thicker compressible filler in notched brick.
method 3 is typically preferred over method 2, although method 1 can be used if shadow line can be created by offsetting brick or some other architectural feature to hide "thickness" of joint.
these considerations and directions that the architect should give you so that shelf angles can be set at the proper elevation. shelf angle thickness usually does not exceed 5/16". mortar joint thickness typically being 3/8". max. movement = 1/2 x comp. filler.
i hope this helps!

oops! i made a mistake on the thickness of the joint for method 1. it should be flashing + shelf angle thickness + compressible filler.
a good reference would also be the brick industry association
__________________
借用达朗贝尔的名言:前进吧,你会得到信心!
[url="http://www.dimcax.com"]几何尺寸与公差标准[/url]
huangyhg离线中   回复时引用此帖
GDT自动化论坛(仅游客可见)
回复


主题工具 搜索本主题
搜索本主题:

高级搜索
显示模式

发帖规则
不可以发表新主题
不可以回复主题
不可以上传附件
不可以编辑您的帖子

vB 代码开启
[IMG]代码开启
HTML代码关闭

相似的主题
主题 主题发起者 论坛 回复 最后发表
brick veneer on 4-story wood bldg huangyhg 产品功能分析 0 2009-09-07 04:57 PM
brick veneer as load bearing huangyhg 产品功能分析 0 2009-09-07 04:55 PM
brick veneer - maximum heights huangyhg 产品功能分析 0 2009-09-07 04:55 PM
brick cladding deflection limits huangyhg 产品功能分析 0 2009-09-07 04:48 PM
bearing on brick veneer a no-no huangyhg 产品功能分析 0 2009-09-07 03:15 PM


所有的时间均为北京时间。 现在的时间是 04:25 AM.


于2004年创办,几何尺寸与公差论坛"致力于产品几何量公差标准GD&T | GPS研究/CAD设计/CAM加工/CMM测量"。免责声明:论坛严禁发布色情反动言论及有关违反国家法律法规内容!情节严重者提供其IP,并配合相关部门进行严厉查处,若內容有涉及侵权,请立即联系我们QQ:44671734。注:此论坛须管理员验证方可发帖。
沪ICP备06057009号-2
更多