huangyhg

mc-3 and mc-4 dimensions
would any of you have reference to the cross-sectional dimensions of these 2 channels, mc-3 and mc-4.
ryerson still supplies these 2 sizes but does not give the dimensions. i am drawing them in solidworks but need the angle of the legs.
thanks.
find a job or post a job opening
my steel book only goes to mc6. thats the smallest i can find. are you sure its not c4 and c3?
do you mean mc3x7.1 (tw=0.312", bf=1.938") and mc4x13.8 (tw=0.500", bf=2.500")? they're in my ryerson catalog, but it doesn't list the flange thickness. my aisc 7th edition gives 3/8" for the average flange thickness of the mc3x7.1.
"do you mean mc3x7.1 (tw=0.312", bf=1.938") and mc4x13.8 (tw=0.500", bf=2.500")? they're in my ryerson catalog, but it doesn't list the flange thickness. my aisc 7th edition gives 3/8" for the average flange thickness of the mc3x7.1"
yes those are the shapes i am referring too. ryerson will still sell them but they will not provide the angles and radius for the legs. i believe they must no longer be supported by aisc or something because no where on the web are the referenced. maybe someone with an old bethelem steel book may have more information. acad and solidworks libraries only go down to mc6 as well.
thanks!
westiemployee,
i have a 1978 edition of the bethlehem structural shapes catalog (no. 32777)
mc3x7.1
design properties:
a = 2.09, d = 3.00, bf= 1.938, tf =0.351, tw = 0.312, ixx = 2.73, sxx = 1.82, rx = 1.14, iyy = 0.712, syy = 0.561, rx = 0.669, eo = 0.730
detailing dimensions:
d = 3, bf = 2, tf = 3/8, tw = 5/16, tw/2 = 1/8, a = 1 5//8, t = 1 3/4, k = 5/8, r = 0.190, grip = not specified, max flange fastener = not specified, usual flange gage g = not specified.
two footnotes apply to this shape:
these channels have a slope of 2.7 degrees. all other channels on these pages have a slope of 2 degrees.
channels similar to mc3 except that flanges flare outward to 3 1/8" across the toe are also available.
mc4x13.8 is not listed
hope this helps.
regards,
chichuck
westiemployee,
aisc gives following properties:
library: aisc13
type: mc
designation = mc3x7.1
w = 7.1
a = 2.11
d = 3
bf = 1.94
tw = 0.312
tf = 0.351
cw = 0.813
kdes = 0.8125
kdet = 0.653
x = 0.574
e0 = 0.414
xp = 2.72
ix = 2.24
zx = 1.81
sx = 1.14
rx = 0.666
iy = 0.998
zy = 0.518
sy = 0.562
ry = 0.0928
j = 0.915
ro = 1.76
h = 0.516
-----------------
library: aisc13
type: mc
designation = mc4x13.8
w = 13.8
a = 4.03
d = 4
bf = 2.5
tw = 0.5
tf = 0.5
cw = 1
kdes = 1
kdet = 0.849
x = 0.643
e0 = 0.508
xp = 8.85
ix = 5.53
zx = 4.43
sx = 1.48
rx = 2.13
iy = 2.4
zy = 1.29
sy = 0.727
ry = 0.373
j = 4.84
ro = 2.23
h = 0.55
westiemployee,
a slight correction:
a = 2.09, d = 3.00, bf= 1.938, tf =0.351, tw = 0.312, ixx = 2.73, sxx = 1.82, rx = 1.14, iyy = 0.712, syy = 0.561, rx = 0.669, eo = 0.730
should read:
a = 2.09, d = 3.00, bf= 1.938, tf =0.351, tw = 0.312, ixx = 2.73, sxx = 1.82, rx = 1.14, iyy = 0.712, syy = 0.561, rx = 0.583, x = 0.669, eo = 0.730
i apologize for the error.
seeing lokstr's post, gee, what do you do now?
regards,
chichuck

__________________
借用达朗贝尔的名言：前进吧，你会得到信心!
[url="http://www.dimcax.com"]几何尺寸与公差标准[/url]