几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量  


返回   几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 » 三维空间:产品设计或CAX软件使用 » CAD设计 » 产品功能分析
用户名
密码
注册 帮助 会员 日历 银行 搜索 今日新帖 标记论坛为已读


 
 
主题工具 搜索本主题 显示模式
旧 2009-09-09, 06:51 PM   #1
huangyhg
超级版主
 
huangyhg的头像
 
注册日期: 04-03
帖子: 18592
精华: 36
现金: 249466 标准币
资产: 1080358888 标准币
huangyhg 向着好的方向发展
默认 ibc section 1907.5 placing reinforcemen

ibc section 1907.5 "placing reinforcement"
does section 1907.5 of the 2006 ibc code prohibit the wet-stabbing of stemwall verts into concrete strip footings. a local building official thinks that it does. personally i think the section is intended to address only primary reinforcement but i may be wrong.
does anyone have any information?
thanks
check out our whitepaper library.
stabbing rebar is a bad practice. whether the ibc section prohibits it or not (i'm not near an ibc right now) doesn't matter. crsi and aci both caution against it. i never allow it.
and in many cases starter bars from strip footings are "primary reinforcement". only the designer knows, so the building official is correct.
while i can't argue that stabbing is bad practice. i can tell you that in my area it is standard practice on small stemwall footings.
the building official was basically asking me if i knew of an "out" for him.
as you can imagine, he is not at all excited about the long, nasty job ahead in dealing with local contractors who have always followed the less costly practice of stabbing verts.
thanks to all
i just read 1907.5 and to me that is pretty clear that stabbing of bars is not allowed.
quote:
reinforcement shall be accurately placed and adequately supported beforefff"> concrete is placed
sounds like the bo was being reasonable in allowing someone to show him some standard that would allow him to accept stabbing the bars.
don phillips
seems to me the code is pretty clear, no stabbing allowed.
it seems to be standard practice in the residential sector, but not the commercial one.
i always advise against it.
__________________
借用达朗贝尔的名言:前进吧,你会得到信心!
[url="http://www.dimcax.com"]几何尺寸与公差标准[/url]
huangyhg离线中   回复时引用此帖
GDT自动化论坛(仅游客可见)
 


主题工具 搜索本主题
搜索本主题:

高级搜索
显示模式

发帖规则
不可以发表新主题
不可以回复主题
不可以上传附件
不可以编辑您的帖子

vB 代码开启
[IMG]代码开启
HTML代码关闭

相似的主题
主题 主题发起者 论坛 回复 最后发表
confused with aisc code about section modulus huangyhg 产品功能分析 0 2009-09-08 01:07 PM
built up section - sction modulus huangyhg 产品功能分析 0 2009-09-07 05:46 PM
section of a section huangyhg tec-ease(America) 0 2009-09-05 12:48 PM
【转帖】section of a section yang686526 American standards 0 2009-04-29 09:53 PM
【转帖】asme美国机械工程师标准目录2 huangyhg American standards 5 2009-04-26 02:38 PM


所有的时间均为北京时间。 现在的时间是 12:16 AM.


于2004年创办,几何尺寸与公差论坛"致力于产品几何量公差标准GD&T | GPS研究/CAD设计/CAM加工/CMM测量"。免责声明:论坛严禁发布色情反动言论及有关违反国家法律法规内容!情节严重者提供其IP,并配合相关部门进行严厉查处,若內容有涉及侵权,请立即联系我们QQ:44671734。注:此论坛须管理员验证方可发帖。
沪ICP备06057009号-2
更多