几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量  


返回   几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 » 三维空间:产品设计或CAX软件使用 » CAD设计 » 产品功能分析
用户名
密码
注册 帮助 会员 日历 银行 搜索 今日新帖 标记论坛为已读


回复
 
主题工具 搜索本主题 显示模式
旧 2009-09-15, 04:20 PM   #1
huangyhg
超级版主
 
huangyhg的头像
 
注册日期: 04-03
帖子: 18592
精华: 36
现金: 249466 标准币
资产: 1080358888 标准币
huangyhg 向着好的方向发展
默认 raising a garage roof 9need help0

raising a garage roof (need help)
i want to know if anyone knows the best way to raise a garage roof. is there any sites that i can go to that would help me find out how to do it. i have 2 car garage and i want to raise the roof about a 2 feet. thanks...
supposing you are speaking about raising the existing roof in place (not rebuilding a new one) this is an operation that might be quite simple for an experienced worker or almost impossible (without destroying the roof or part of the walls) depending on the type and status of the structure.
you should better specify this, but guess it will be impossible to give good advice without looking at the real thing: the best advice is to consult a local construction company.
prex
the easiest method is moving>
depending on how your garage is put together it is often easier to disconnect from the foundation and jack up the entire structure. you then either build a new poney wall under it or pour a higher perimeter wall foundation. either way it is a lot of work and tricky but can be easier than disconnecting and trying to raise all the roof trusses or framing. you usually can't remove the roof from the sidewalls without taking off the siding.
you will want someone who understands how the loads are transferred to the foundation to look at it before you act (i.e. structural engineer) or it may fall down in the next big wind storm. i assume you are wanting to raise the roof so you can put on taller doors and put an rv inside. good luck and i hope the rv is worth the trouble.
__________________
借用达朗贝尔的名言:前进吧,你会得到信心!
[url="http://www.dimcax.com"]几何尺寸与公差标准[/url]
huangyhg离线中   回复时引用此帖
GDT自动化论坛(仅游客可见)
回复


主题工具 搜索本主题
搜索本主题:

高级搜索
显示模式

发帖规则
不可以发表新主题
不可以回复主题
不可以上传附件
不可以编辑您的帖子

vB 代码开启
[IMG]代码开启
HTML代码关闭

相似的主题
主题 主题发起者 论坛 回复 最后发表
perpendicular roof wind pressures huangyhg 产品功能分析 0 2009-09-15 12:13 PM
low slope roof construction huangyhg 产品功能分析 0 2009-09-10 11:50 AM
gypsum roof huangyhg 产品功能分析 0 2009-09-09 03:37 PM
flat roof repairs huangyhg 产品功能分析 0 2009-09-09 12:23 PM
asce figure 6-10 wind loads huangyhg 产品功能分析 0 2009-09-07 01:22 PM


所有的时间均为北京时间。 现在的时间是 10:32 PM.


于2004年创办,几何尺寸与公差论坛"致力于产品几何量公差标准GD&T | GPS研究/CAD设计/CAM加工/CMM测量"。免责声明:论坛严禁发布色情反动言论及有关违反国家法律法规内容!情节严重者提供其IP,并配合相关部门进行严厉查处,若內容有涉及侵权,请立即联系我们QQ:44671734。注:此论坛须管理员验证方可发帖。
沪ICP备06057009号-2
更多