几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量  


返回   几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 » 三维空间:产品设计或CAX软件使用 » CAD设计 » 产品功能分析
用户名
密码
注册 帮助 会员 日历 银行 搜索 今日新帖 标记论坛为已读


回复
 
主题工具 搜索本主题 显示模式
旧 2009-09-16, 05:27 PM   #1
huangyhg
超级版主
 
huangyhg的头像
 
注册日期: 04-03
帖子: 18592
精华: 36
现金: 249466 标准币
资产: 1080358888 标准币
huangyhg 向着好的方向发展
默认 upgrading wood columns in an old building

upgrading wood columns in an old building
i'm working on load rating an existing unreinforced masonry building with wood floor systems and interior wood columns. the owner would like to upgrade the floor capacities, which is governed by the lowest level of wood columns (this is an old 5 story factory building). i innitially checked building up the existing columns with additional wood members, but the member stresses were still pretty high. i'm thinking about sandwiching channels to the columns. can anyone point me in the right direction?
thanks.

i think the key would be the load path from the existing floor into whatever type of column steel upgrading you would provide, be it channels or something else.
at each floor, there is now some means of transferring the load from the floor into the column. so your final design would want to include consideration for:
1. how to get the floor load into the new steel shapes.
2. how to get the column loads in the upper stories into the steel shapes at the lower columns.
how are the foundation doing? sounds like what you should do is based on what you can see, rate it and restrict it. if you plan to reinforce above grade structure to increase capacity then get a geotechnical component going.
the old buildings usually have pintels (cast iron?) transfering the load from one column to the next. i do not how to rate these other then testing. do you have to consider uplift in the top story?
jae: the load transfer from the floors to the channels has been a concern. the pintels protrude past the columns and make for a realy messy detail. the more we look at it, it seems the right thing to do will be to replace the wood columns with steel at the lower levels. caps and bases could be easily fabricated to take the place of the pintels and provide a means for anchoring each column to the one below.
jike: thanks for the reminder, all of the upper levels of wood columns will require straps to resist the uplift.
connect2: there are ledge outcroppings throughout this basement, and i have not found any signs of settlement. i suspect everything is found on solid foundations, however we cannot tell for certain. the joists and beams max out at around 50-55 psf, and i don't intend to bump up this somewhat low rating.
the lowest level of columns appear to be too light for snow load coupled with the 55 psf on all the floors above. in order to get the stresses down, i'd have to vacate a couple of floors.
have you considered llr?
mike mccann
mccann engineering
msquared48: i am using llr in the design of replacement and/or reinforcing, but did not in the existing conditions since the floor member capacities were below the ibc 2006 loads for new structures. the way i read the llr section was that it could only be applied to the values in table 1607.1 (125psf if this was new construction)?
the reinforcement/replacement will be designed for current codes (125 psf with applicable llr), although the floor members will still only be rated at the 50-55 psf.
__________________
借用达朗贝尔的名言:前进吧,你会得到信心!
[url="http://www.dimcax.com"]几何尺寸与公差标准[/url]
huangyhg离线中   回复时引用此帖
GDT自动化论坛(仅游客可见)
回复


主题工具 搜索本主题
搜索本主题:

高级搜索
显示模式

发帖规则
不可以发表新主题
不可以回复主题
不可以上传附件
不可以编辑您的帖子

vB 代码开启
[IMG]代码开启
HTML代码关闭

相似的主题
主题 主题发起者 论坛 回复 最后发表
round wood columns huangyhg 产品功能分析 0 2009-09-15 07:39 PM
pre-engineered metal building engineer sse or ser huangyhg 产品功能分析 0 2009-09-15 02:08 PM
designing columns for concrete buildings huangyhg 产品功能分析 0 2009-09-08 06:12 PM
5 story wood building huangyhg 产品功能分析 0 2009-09-07 08:50 AM
4 story wood building with steel beams and columns at the fi huangyhg 产品功能分析 0 2009-09-07 08:45 AM


所有的时间均为北京时间。 现在的时间是 06:32 AM.


于2004年创办,几何尺寸与公差论坛"致力于产品几何量公差标准GD&T | GPS研究/CAD设计/CAM加工/CMM测量"。免责声明:论坛严禁发布色情反动言论及有关违反国家法律法规内容!情节严重者提供其IP,并配合相关部门进行严厉查处,若內容有涉及侵权,请立即联系我们QQ:44671734。注:此论坛须管理员验证方可发帖。
沪ICP备06057009号-2
更多