几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量  


返回   几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 » 三维空间:产品设计或CAX软件使用 » CAD设计 » 产品功能分析
用户名
密码
注册 帮助 会员 日历 银行 搜索 今日新帖 标记论坛为已读


 
 
主题工具 搜索本主题 显示模式
旧 2009-09-15, 01:57 PM   #1
huangyhg
超级版主
 
huangyhg的头像
 
注册日期: 04-03
帖子: 18592
精华: 36
现金: 249466 标准币
资产: 1080358888 标准币
huangyhg 向着好的方向发展
默认 pound per square inch compared to pound per linear inch

pound per square inch compared to pound per linear inch
hi,
i need to compare pound per linear inch to pound per square inch. i am right to figure that if it is 10 pounds per linear inch, that then it would be 100 pounds per square inch?
it depends on the span.
you'll need to give a little better information. i can't make sense of what you are asking or how you got 100 from 10.
all right, i have an aluminum spacer ring that has a cross section of .21 in. by .093 in. tall. it is fastened down so that there is a holding force of 60 psi. there is a gasket whose spec is roughly that it requires 20 pounds per linear inch to deform to the point of metal to metal contact. i need to be able to compute pounds per linear inch.
ok, i guess i shouldn't have asked. a width in inches times a pressure in psi would give you pli.
thanks.
i know i'm pedantic, but a force is means in lbs and a pressure (a force acting over an area) is measured in psi.
if the gasket requires 20 lbs/in to deflect, how long is it ... that's the force required, call it 20l lbs.
if you have a pressure acting, i assume that the gasket make
s a closed loop ... enclosing an area, so if you have 60psi acting over an area, ain2, then you have a force of 60a lbs.
rb1957,
the spec is for pounds per linear inch, not pounds per inch. the force required is as structuralaggie has defined it (psi * width).
what is the difference between pounds per linear inch and pounds per inch?
it helps when you put the units as fraction instead of abbreviation.
thx whyun, you beat me to it
makes sense (from the rubber fabricator's standpoint at least!) for him to specify pounds per linear inch of his gasket, because he doesn't know how big an o-ring (how far around/what dia) the o-ring is going to become.
so he specifies pounds per inch of (his) rubber. then sells thousands of o-rings of various diameters, and as linear seals for rectangular lids and covers. the mechanical engineer then has to decide on what pressure he will put on the o-ring by deciding the number of bolts, torque, and length of the seal.
warning: welds are also specified by pounds per inch ... but that is how much force the weld (of some electrode, and some fillet height and width) can handle per inch length of the weld.
__________________
借用达朗贝尔的名言:前进吧,你会得到信心!
[url="http://www.dimcax.com"]几何尺寸与公差标准[/url]
huangyhg离线中   回复时引用此帖
GDT自动化论坛(仅游客可见)
 


主题工具 搜索本主题
搜索本主题:

高级搜索
显示模式

发帖规则
不可以发表新主题
不可以回复主题
不可以上传附件
不可以编辑您的帖子

vB 代码开启
[IMG]代码开启
HTML代码关闭

相似的主题
主题 主题发起者 论坛 回复 最后发表
how do you know if a problem is linear huangyhg 产品功能分析 0 2009-09-09 05:24 PM
【转帖】asmeb107.100-2002-b94.9-1999标准 huangyhg American standards 1 2009-09-01 09:28 AM
【转帖】asme美国机械工程师标准目录2 huangyhg American standards 5 2009-04-26 02:38 PM


所有的时间均为北京时间。 现在的时间是 06:40 PM.


于2004年创办,几何尺寸与公差论坛"致力于产品几何量公差标准GD&T | GPS研究/CAD设计/CAM加工/CMM测量"。免责声明:论坛严禁发布色情反动言论及有关违反国家法律法规内容!情节严重者提供其IP,并配合相关部门进行严厉查处,若內容有涉及侵权,请立即联系我们QQ:44671734。注:此论坛须管理员验证方可发帖。
沪ICP备06057009号-2
更多