几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量  


返回   几何尺寸与公差论坛------致力于产品几何量公差标准GD&T (GDT:ASME)|New GPS(ISO)研究/CAD设计/CAM加工/CMM测量 » 三维空间:产品设计或CAX软件使用 » CAD设计 » 产品功能分析
用户名
密码
注册 帮助 会员 日历 银行 搜索 今日新帖 标记论坛为已读


回复
 
主题工具 搜索本主题 显示模式
旧 2009-09-10, 12:30 PM   #1
huangyhg
超级版主
 
huangyhg的头像
 
注册日期: 04-03
帖子: 18592
精华: 36
现金: 249466 标准币
资产: 1080358888 标准币
huangyhg 向着好的方向发展
默认 masonry connection to concrete

masonry connection to concrete
hi,
i have just joined eng-tips so i hope that i can get an answer to this question. i have to design an 8ft tall, 8in cmu wall to an existing concrete slab so i am wondering where i can find details or information on doweling requirements and epoxy use.
can anyone help or direct me?
thanks.
check out our whitepaper library.
the simpson catalog has a lot of information on their epoxy for retrofitting and the same material could be used in this application very easily for doweled-in rebar.
a few questions:
is your connection "simple" requiring less embedment, or does the connection have to resist moment? is the new cmu wall bearing and/or shear, or is it only a partition wall? do you know the depth of the existing strip footing, or will you have to sawcut and create a new strip footing to take the load?
your answers reflect the required embedment. logically, if you have to sawcut the slab to create a new footing, you will not need to epoxy the dowels.
mike mccann
mccann engineering
is the wall supported at the top or is it cantilevered?
dik
you also probably can try- hilti hit re-150 or re-500, hilti anchorfix adhesive etc. all of these are widely used epoxies for retrofitting, doweling-in.
try the web site-
the reason i asked if the wall was cantilevered is that it may not be necessary to dowel the wall to the slab. mortar bedding on clean dampened concrete and lateral support at the top. depending on jurisdiction and practice, you may be able to use 6" cmu's for 8' height.if you are required to provide dowels, then the hilti hit system, noted by shin25, is one of the better ones.
dik
thanks for the help all.
the wall is cantilevered so it will have to resist moments at the base, and it is essentially a partition wall. i am not sure of the thickness of the existing slab but i have been told to assume that it is 6inches thick. i cannot sawcut through the slab due to certain restaints so it means that the slab has to be doweled into, to connect the wall.
i will refer to the website suggested though.
depending on the loading, an 8" cmu wall cantilevered 8' may be a bit dodgy... anchorage would be critical and also rebar splices are normally greater...
dik
if you are not certain of the slab thickness or reinforcing, can you be certain that the slab will be able to withstand the moment it receives from the base of the wall?
i know that not knowing the slab thickness is also a problem. but for now, i am required to come up with some preliminary rebar for the wall and method of connection between the new wall and the existing slab.
i just graduated so i guess i assumed that doing things this way (making assumptions) is common.
if your assumptions are wrong, how do you propose to fix the failure?
i dont think that they intend to build the wall until all the relevant information becomes available because that will place liability on us should there be a failure. however, they do want some kind of design or preliminary drawings to start with.
__________________
借用达朗贝尔的名言:前进吧,你会得到信心!
[url="http://www.dimcax.com"]几何尺寸与公差标准[/url]
huangyhg离线中   回复时引用此帖
GDT自动化论坛(仅游客可见)
回复


主题工具 搜索本主题
搜索本主题:

高级搜索
显示模式

发帖规则
不可以发表新主题
不可以回复主题
不可以上传附件
不可以编辑您的帖子

vB 代码开启
[IMG]代码开启
HTML代码关闭

相似的主题
主题 主题发起者 论坛 回复 最后发表
masonry cemen huangyhg 产品功能分析 0 2009-09-10 12:28 PM
concrete sampling guidlines huangyhg 产品功能分析 0 2009-09-08 12:34 PM
concrete mix= reinfocing for exterior composit deck huangyhg 产品功能分析 0 2009-09-08 12:19 PM
concrete corrosion in partial saturated condition huangyhg 产品功能分析 0 2009-09-08 11:54 AM
chapter 4 preliminary design properties of concrete huangyhg 产品功能分析 0 2009-09-07 11:23 PM


所有的时间均为北京时间。 现在的时间是 11:11 PM.


于2004年创办,几何尺寸与公差论坛"致力于产品几何量公差标准GD&T | GPS研究/CAD设计/CAM加工/CMM测量"。免责声明:论坛严禁发布色情反动言论及有关违反国家法律法规内容!情节严重者提供其IP,并配合相关部门进行严厉查处,若內容有涉及侵权,请立即联系我们QQ:44671734。注:此论坛须管理员验证方可发帖。
沪ICP备06057009号-2
更多